[http command]

1 time siden, Mikkel Skovgaard skrev:

Yes there is a soap XML API but its not something that is documented in anyway. It requires a login first, then cookies stored and a call. There is plenty of discussion about it in here when we started decoding it. It's pretty flawed

Can you give me the link?

[http command]

32 minutter siden, Mikkel Skovgaard skrev:

Você precisa de um pedaço de software, se você quer apenas na maneira estática é muito fácil de codificar se você olhar para alguns dos exemplos. Você também pode tentar IHC capitão ou ponte IHC

IHC Captain or IHC Bridge require Hardware (raspberry pi) and I want a software solution like command fusion for example. If the IHC has an IP address and has well-defined IOs, there must be some way to send commands to it outside the java interface.

[http command]

Lige nu, Mikkel Skovgaard skrev:

You want to send commands to the IHC controller or from the controller

To IHC controller

[http command]

På 18/07/2019 at 00:18 , Mikkel Skovgaard skrev:

Explicar?

The IHC is configured on the network with a specific IP address and a Port, correct?
I would like to know if from this address I can send http commands via hyperterminal and / or any internet browser without going through the IHC java application.

[http command]

Is there any way to do commands on IHC via the internet, for example, writing the google chrome layer  contollerip:port command 

[Opdatering til IHC remote version 1.4.5]

9 timer siden, SimonL skrev:

I did not downgrade it as the update didn't work. I used the firmwareloader 1.3.3. After I tried upgrading with no result I turned off the power for a while eg. 5 min. and tried again with the same update. 

I tried 10 times and I gave up, it always gives an error in 74%

[Opdatering til IHC remote version 1.4.5]

På 6.12.2018 at 14:47 , SimonL skrev:

Ja den er stabil. Mærker ikke noget hastighedsproblem eller noget som helst. Jeg kan også connecte med app på iPhone igen. 

When it was an error, did you downgrade 2.8.4 firmware or did it again? And you used firmwareloader 1.3.3 or 1.0?
Thank you

[IOS 11 og LK]

And for my problem of serial number and RF version without their numbers. can anybody help me?

[IOS 11 og LK]

2 timer siden, Bjarne Sørensen skrev:

What if you bye an used Visual 2 controller from Denmark? Will you get the a huge tax ticket too?

Every imported product goes through a human check. If the person who is checking my IHC searches the value of it in the home country, it should tax the same at 60% of the value.
I would have to take that risk and hope not to be taxed.

Brazil is the country that most likes to collect taxes in the world.

[IOS 11 og LK]

På 11/11/2017 at 11:16 , Lars Jacobsen skrev:

Verry Strange with The serial number beeing 0.

There was some info about opgrading controllers to latest firmware  didn't help or work on some old controllers that could not show the RF version. Yours don't show the version so that might be the reason, but that is a bit strange sinse yours has a newer production date than Jimmies.

I have no other ideas on how to solve this problem and success opgrading it to 2.8.4

Another solution could be that you contacted one that would sell a used HW ver 6.2 (or even a new ver.3) and shipped it to Brazil.  Should not be any problem today wit PayPal and fedex etc.

Importing in Brazil is just for the crazy, we have to pay at least 60% tax on the value of the product, it would be very expensive for me.
Would you have some old versions of firmware that I could test to see if my controller returns to normal with the serial number?
From the photos you can see that he is in perfect condition right.
Thank you

[IOS 11 og LK]

På 24/10/2017 at 11:59 , Lars1 skrev:

I've never seen a controller with Serial number 0 before, so I can't tell you whether it's a HW or SW problem. Together with the firmware upload problem you have, it points at a HW problem IMHO.

På 24/10/2017 at 17:55 , Lars Jacobsen skrev:

Should be straight ahead. Just disassamble and check for loose boards. They should be placed firmly in The sockets.

There where some treads about it here on Ihc-user.dk and some pictures i recall, but cant find them or any links to the issue anymore...

På 08/11/2017 at 11:15 , Lars1 skrev:

The install sequence doesn't matter. Your problem is probably the default installation is 64bit Java. You often need 32 bit Java for the browser to support Java, and not all browsers support Java.

Once 32bit Java is installed, when you update Java it will update the 32bit version, but you might havepick the 32bit version manually for the first time installation.

I created the courage and I dismounted the IHC, very simple of course, just release the two rear latches and the front cover that has full access to the circuit.
I taked some pictures to show how are my controller, and from what I realized there is only one connector that is what connects the main board to the USB, RF and I / O's card - it was well connected but I wiped the entire board before reconnect and reassemble the equipment.
I tried again pass the 2.8.4 firmware and the same error continues at the end of the installation and the serial number 0 appears in the administrator.
To try to solve the problem, I have the firmware reset_factory_default.zip that has
here in the forum before putting 2.7.220 again and nothing has changed.
With respect to JAVA, I have installed the 32bit version of 7.79 because it is the only one that does not give errors to access.
You would have some other hint tip to help, a master firmware that can sometimes cause the controller to return to factory state.
I am from Brazil, and here Schneider Electric has discontinued the IHC line and works only with KNX, that is, I do not even have the option to buy a new controller version 3 to solve my connection problem with IOS11.
All the help is of immense value.
Thank you so much

 

 

[IOS 11 og LK]

15 timer siden, Jimmi Højkilde skrev:

had same problem as some of the other users in here.. could get the link to work..
Have created this link:
https://drive.google.com/file/d/1iiZXk19PYKBXyWbzXp4mECmD-IqiKtxX/view?usp=sharing
gdrivelink

had to update Java as well...

I have zipped both old and new firmware versions if needed..

My controller is a hw. version 6.1 with visual..

What was your install sequence?
First firmware and then JAVA?
I'm still in error here.

[IOS 11 og LK]

På 19/10/2017 at 18:08 , Lars1 skrev:

Desculpe. Esqueceu o novo carregador de firmware verifica a compatibilidade HW e você possui um controlador HW 6.1.

Eu não tenho outras idéias, mas acabei de dar uma olhada na tela de visualização da administração. É muito estranho que seu número de série seja 0. Eu acho que há algo errado com seu controlador.

Good morning, when I pass the new firmware I wait until the success message, restart the controller and go to the administrator to see these options, can you tell me if there is any hardware or software problem in it?

 

På 19/10/2017 at 14:01 , Lars Jacobsen skrev:

Siden det er en gammel controller uden garanti kan du prøve at åbne det og se om alle boards er korrekt tilsluttet. Der har været rapporter hvor ultima fejler på grund af loose (memória) placas.

 

Any tips for disassembling the controller or is it easy to identify such problems on the board?

[IOS 11 og LK]

4 timer siden, Lars Jacobsen skrev:

Since it is an old controller without warranty you could try opening it and see if all boards are properly connected. There has been reports where loading fails because of loose (memory)boards.

 

Could you give me any tips or do you have some disassembly tutorial of the controller?,

I'll do it tomorrow morning to try to finish it the same day.

[IOS 11 og LK]

8 timer siden, Lars1 skrev:

1. Remove the network cable from the controller
2. Remove the power for 10 sec.
3. Upgrade to firmware 2.8.4 using the firmware loader which comes with Visual 2.8.6. You need to install that version of Visual anyway in order to make changes to the program after the the firmware upgrade.
4. Connect the network cable once you have successfully upgraded the firmware.

If this doesn't work, I don't have any better ideas.

I did all the procedures, however, with the old firmware loader here from the forum, since with version 2.8.6 gave the error below.
I believe that I will not get anything right, right?

[IOS 11 og LK]

På 17/10/2017 at 06:48 , Lars1 skrev:

O problema com a atualização da interface de rádio e a parada em 80% são 2 problemas diferentes.

Eu tentaria downgrading para 2.7.199, retire a energia para o controlador por pelo menos 10 segundos. e então tente atualizar para 2.8.4. Por algum motivo, parece que o controlador não inicializa corretamente. Não deve haver N / A na versão de RF e série de RF quando você olha a visualização de administração.

Good morning, I was traveling and I returned today to do the tests.
Regarding the radio version being in N / A for me is not a problem since I do not use RF and I do not have an antenna installed on the IHC Controller.
As for uploading to 2.8.4 firmware I did several tests and all with the same error at 75%:
- first downgraded to 1.7.199, hung up for 10 seconds and tried to 2.8.4 - error
- then I used the firmware "reset_factory_default" available here in the forum and did the same procedure - error.
I tried even disconnecting all the I/O's from the controller.

What will be more than I can try? I tried to up the firmwares 2.8.1 and 2.8.3 and both gave the same error in the 75%
Am I doing anything wrong? 
Just a detail to pass, my IHC software is in version 2.7.349 in English and the firmware loader is that I am using aqiu of the forum is in Danish, can this be a problem?
Thank you

På 16/10/2017 at 18:19 , Kandersen skrev:

Você pode recarregar o fw 2.7.220 no controlador sem problemas?
Talvez você tenha um se esses controladores não forem possíveis de atualizar. Acho que Lars1 mencionou um há alguns dias atrás. Como me lembro, havia algo sobre a interface de rádio. Men jeg er ikke sikker på om det får en fejl når du prøver. Talvez Lars1 possa contar mais sobre isso.

I did numerous tests with several firmwares, all above 2.7.220 give an error but I can go back to 2.7.220 without errors.
Regarding the radio version, I have no antenna installed and I have never used RF so this could be a problem in the update?

Thank you

[IOS 11 og LK]

17 minutter siden, Kandersen skrev:

Eu não fiz nada de especial. Basta iniciar o carregador de firmware, conectado ao controlador. Escolheu o arquivo de firmware, e fora ele foi com sucesso. 

 

O firmware é adicionado a esta mensagem.

IHC 2.8.4.fwf

Thanks, but here it continues giving error to transfer the firmware 2.8.4

[IOS 11 og LK]

20 minutter siden, Brian Hansen skrev:

Eu testei isso no fim de semana. E pode correr bem, mas acho que está funcionando se houver muita informação ao mesmo tempo. Tenho alarme Ihc e 8 quartos sentem-se como aquecimento de piso. Abaixei o firmware antigo novamente para fazê-lo funcionar corretamente, infelizmente. 

And did you do some non-standard procedure (disconnect something, for example)?

[IOS 11 og LK]

4 timer siden, Kandersen skrev:

Você usou o mesmo carregador de firmware?
Talvez você deva tentar baixar o firmware novamente. Eu notei que a Lk não embala o firmware em um arquivo zip. Pode ser que o download tenha sido corrompido de alguma forma. Caso contrário, eu não tenho ideia. Funcionou bem para mim ontem à noite, quando usava o carregador de firmware 1.3.3 sugerido por TorbenSørensen acima. 

I used the firmware loader from Torben link above (1.3.3) and I downloaded o firmware directly from the lk.dk site and it always gives 75% error even downloading the firmware (14,426,112 bytes) several times. And did you do some non-standard procedure (disconnect something, for example)?
Could you pass the firmware that was used in my email - tiagobritici@hotmail.com for me to test if the problem is even in the file?
Thank you

[IOS 11 og LK]

I'm trying to do this on my 6.1 controller with visual and it's giving error.
Could you tell me how you could upgrade?
I tried straight through from 2.7.220 to 2.8.4 and when it reaches 80% it gives error and the controller no longer responds.
Thank you

[Controller ingen kontakt]

I have a similar problem. I Could not login with admin user. I created a new user as administrator and everything is ok.

[Problems with IOS11]

1 time siden, Lars Jacobsen skrev:

Não funcionará. 

O HW 6.1 não é suportado pelo período ios11. Não há solução alternativa.

I have the old firmware loader.
Can I put the firmware in 6.1 or will it crash?

[Problems with IOS11]

I have an IHC HW6.1 controller and can no longer communicate with the IHC Remote after upgrading from IOS11 to smartphones. Could you help me?

I'm thinking of loading 2.8.4 firmware with an old firmware loader. Can I have problems?

 

[Questions about IHC]

44 minutter siden, Lars Jacobsen skrev:

Alguns comentários:

LK tem um aplicativo para iPad chamado IHC Tablet que pode acces e controlar vários controlleres. Mas, se eles têm que ser visibel e controlador de Internet, você precisa fazer o encaminhamento de porta somme no seu roteador se ambos controllere estão na mesma rede local.

 

 

I don´t have a iPad, smartphone Android 6.0 and iMac.

[Questions about IHC]

Thank you Lars1.
I want to better understand your answer regarding question 3.
I am from Brazil, here we have no way to acquire Visility Board, and our idea would be a software solution and not hardware as with the others too, I did not understand much about the IHC Captain, OpenHab and Domoticz but from what I saw, I have to have A server on the IHC controller, and believe me here in Brazil, this is very expensive. Would you have any option only via software?
From question 4, I have the latest version of FW from IHC 2.7.220 and I do not have remote access success, I searched a lot here and did not find anything, if you can give me a hand I will be eternally grateful.
Thanks a lot for the help.